Ecotech-marine MP20 Manuel d'utilisateur télécharger pdf

To remove the nozzle from the wet frame, remove the entire wet half of the pump from the aquarium and

place it on a non-metallic surface. Gently but firmly press down on the nozzle with your palm and twist coun-

ter clockwise. The nozzle should become free of the wet frame. It may then be cleaned of any obstructions.

Specifications and Operating Parameters

Flow: 500-2000 gallons/hour, Power: 6-18 watts,

Aquarium Wall Thickness: 3/16” to 3/4”

Your VorTech propeller pump

Before you start

Preparation

Once you have chosen the location where you wish to install your VorTech pump, clean away any algae, calcified or

otherwise, using a razor blade.

Notes on placement

The VorTech creates over 2000 gallons per hour of low velocity flow within your aquarium. Take care to place the

VorTech in a suitable location where corals are not directly in the line of flow. Place the pump sufficiently high enough

above a fine sand bed so that sand is not blown around by the output or undertow created by the VorTech.

Protect the pump from water

The VorTech’s motor housing and driver are NOT WATERPROOF. Any water allowed into these components can damage

them enough to require replacement. This kind of damage is NOT covered in the VorTech’s warranty. Protect these

components from splashes of any kind.

Adjust the pin spacer

The VorTech pump is designed to operate with a constant gap between both halves of

the device. The pin spacer is used to ensure the proper spacing for various aquarium wall

thicknesses.

Make sure to measure your aquarium’s glass thickness using a ruler or contact the aquari-•

um manufacturer in order to determine the exact thickness.

To adjust for the proper aquarium thickness, pull the pin spacer from the motor housing. •

Then align the VorTech’s power cord emerging from the motor with your aquarium’s wall

thickness to achieve the proper offset from your aquarium.

Note: 3/4” thick aquariums do not use the pin spacer at all.

IMPORTANT: When adjusting the pin spacer, be sure not to bend the pins as they are inserted into the

holes within the heat sink as this may permanently damage your VorTech. Bent pins WILL NOT be covered

under warranty.

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Adjust the pin spacer

To remove the nozzle from the wet frame, remove the entire wet half of the pump from the aquarium and place it on a non-metallic surface. Gently but

Page 2 - Align the VorTech

2The VorTech utilizes very powerful magnets and can cause severe personal injury.•NEVER connect the two halves of this device without a proper space

Page 3 - Wave Motion Warning

Your VorTech Wave DriverWave Motion WarningThe generation of waves within your aquarium places additional stress on the aquarium glass and joints. N

Page 4 - General Operational Modes

4Lagoon Random ModeWhen a pump is in Lagoon Random Mode, the dial is used to set the maximum operational speed, and the driver will automatically rand

Page 5 - Advanced Features

Advanced FeaturesStep 2) Press and hold Mode and Set to enter Setup. The LED will blink red/white/blueAfter programming Night Mode, the pump will

Page 6 - Troubleshooting

Wear of the drive shaftThe VorTech pump features a wear component in the form of the drive shaft. This part is designed with a special engineering g

Page 7 - Customer Support

WarrantyCustomer [email protected](610) 954-8480Sales inquiries please contact:[email protected](800) 785-0338EcoTech Marine warr

Page 8

This product carries an ingress protection rating of IPX0 and must not be immersed in water.Danger: To avoid possible electrical shock, special care

Commentaires sur ces manuels

Pas de commentaire

Ecotech-marine MP20 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pompes Ecotech-marine MP20. EcoTech Marine MP20 User Manual [cs] [en] [pl] [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes Ecotech-marine MP20